Fisher & Paykel Washer WL80T65D. Fisher & Paykel Clothes Washer Installation Instructions and User Guide. Showing Products 1 - 31 of 31. We design and engineer our appliances to stand the test of time. However, should you require help, no one is better to service your product than a Fisher & Paykel technician or authorized service partner. Our technicians are equipped with diagnostic tools and only use genuine parts to service your Fisher & Paykel appliances.
Fisher & Paykel Gwl11 Service Manual
Download 62 pages, 3.91 MbFisher Paykel Service Manual
6.3“See Manual” Error Codes
The following is an explanation of the error codes that are displayed in conjunction with the See Manual indicator flashing. A code is not displayed if the microprocessor has stopped functioning (see technical problems - section 6.2).
Error | Description of Fault | |
E00 | No fault | |
E02 | Microprocessor stack overflow | |
E03 | RAM fault | |
E04 | ROM fault | |
E05 | EEPROM version older than ROM version. Update EEPROM. Refer to Section 7.2.6 | |
E06 | EEPROM version newer than ROM version – (old software). Contact Fisher & Paykel | |
Healthcare | ||
E07 | Model mismatch with software, contact your Fisher & Paykel Healthcare | |
representative. | ||
NOTE: included in software version 7.14 onward, except 7.21. | ||
E10 | Temperature circuit calibration out of range: Range Amp 0: 25.5 °C | |
E11 | Temperature circuit calibration out of range: Range Amp 0: 65.0 °C | |
E12 | Temperature circuit calibration out of range: Range Amp 1: 25.5 °C | |
E13 | Temperature circuit calibration out of range: Range Amp 1: 34.5 °C | |
E14 | Temperature circuit calibration out of range: Range Amp 2: 34.5 °C | |
E15 | Temperature circuit calibration out of range: Range Amp 2: 44.6 °C | |
E16 | Temperature circuit calibration out of range: Range Amp 3: 65.0 °C | |
E20 | Heater wire circuit has malfunctioned, heater can not be energized: | |
- Heater plate thermal cutout tripped (section 7.2.5) | ||
- Heater wire fuse (F2) is open circuit (section 7.2.2) | ||
- Heater wire triac, or heater wire relay is open circuit | ||
E21 | Heater wire circuit has malfunctioned, heater either can not be | |
monitoring circuit has failed : | ||
- Heater wire triac has shorted | ||
- Heater wire sense circuit has failed | ||
E23 | Heater wire voltage measurement circuit faulty | |
E25 | Transistor Q17 is not turning on | |
E26 | Transistor Q16 is not turning on | |
E27 | The heater wire relay is short circuited | |
E28 | Mains voltage measurement is uncalibrated (section 8.1.3) | |
E29 | The heater plate thermistor is short circuited | |
E2A | The heater plate thermistor is open circuit | |
E2C | Heater plate element circuit has malfunctioned is not turning on: | |
- Element is open circuit | ||
- Heater plate triac or driver faulty | ||
- Heater plate relay is faulty | ||
E2D | The heater plate element is not turning off. Heater plate triac circuit faulty. | |
E30 | Power (on/off) button stuck on | |
E31 | Mute button stuck on | |
E32 | Mode button stuck on | |
E40 | Unit not functional tested at time of manufacture | |
MR850 Technical Manual * Revision J * Issued November 2005 * Ref. 185041340 (185041713 internal) | 27 | |
6.3“See Manual” Error Codes
Fisher Paykel Owners Manual
The following is an explanation of the error codes that are displayed in conjunction with the See Manual indicator flashing. A code is not displayed if the microprocessor has stopped functioning (see technical problems - section 6.2).
Error | Description of Fault | |
E00 | No fault | |
E02 | Microprocessor stack overflow | |
E03 | RAM fault | |
E04 | ROM fault | |
E05 | EEPROM version older than ROM version. Update EEPROM. Refer to Section 7.2.6 | |
E06 | EEPROM version newer than ROM version – (old software). Contact Fisher & Paykel | |
Healthcare | ||
E07 | Model mismatch with software, contact your Fisher & Paykel Healthcare | |
representative. | ||
NOTE: included in software version 7.14 onward, except 7.21. | ||
E10 | Temperature circuit calibration out of range: Range Amp 0: 25.5 °C | |
E11 | Temperature circuit calibration out of range: Range Amp 0: 65.0 °C | |
E12 | Temperature circuit calibration out of range: Range Amp 1: 25.5 °C | |
E13 | Temperature circuit calibration out of range: Range Amp 1: 34.5 °C | |
E14 | Temperature circuit calibration out of range: Range Amp 2: 34.5 °C | |
E15 | Temperature circuit calibration out of range: Range Amp 2: 44.6 °C | |
E16 | Temperature circuit calibration out of range: Range Amp 3: 65.0 °C | |
E20 | Heater wire circuit has malfunctioned, heater can not be energized: | |
- Heater plate thermal cutout tripped (section 7.2.5) | ||
- Heater wire fuse (F2) is open circuit (section 7.2.2) | ||
- Heater wire triac, or heater wire relay is open circuit | ||
E21 | Heater wire circuit has malfunctioned, heater either can not be | |
monitoring circuit has failed : | ||
- Heater wire triac has shorted | ||
- Heater wire sense circuit has failed | ||
E23 | Heater wire voltage measurement circuit faulty | |
E25 | Transistor Q17 is not turning on | |
E26 | Transistor Q16 is not turning on | |
E27 | The heater wire relay is short circuited | |
E28 | Mains voltage measurement is uncalibrated (section 8.1.3) | |
E29 | The heater plate thermistor is short circuited | |
E2A | The heater plate thermistor is open circuit | |
E2C | Heater plate element circuit has malfunctioned is not turning on: | |
- Element is open circuit | ||
- Heater plate triac or driver faulty | ||
- Heater plate relay is faulty | ||
E2D | The heater plate element is not turning off. Heater plate triac circuit faulty. | |
E30 | Power (on/off) button stuck on | |
E31 | Mute button stuck on | |
E32 | Mode button stuck on | |
E40 | Unit not functional tested at time of manufacture | |
MR850 Technical Manual * Revision J * Issued November 2005 * Ref. 185041340 (185041713 internal) | 27 | |